| SPECIFICATIONS |
| OUTPUT |
|
| Model |
DR-60-5 |
DR-60-12 |
DR-60-15 |
DR-60-24 |
| DC Voltage |
5V |
12V |
15V |
24V |
| Rated Current |
6.5A |
4.5A |
4A |
2.5A |
| Current Range |
0-6.5A |
0-4.5A |
0-4A |
0-2.5A |
| Rated Power |
32.5W |
54W |
60W |
60W |
| Ripple & Noise |
80mVp-p |
120mVp-p |
120mVp-p |
150mVp-p |
| Voltage Adj. Range |
4.75-5.5V |
11.1-13.2V |
13.5-16.5V |
21.6-26.4V |
| Voltage Tolerance |
±2% |
±1% |
±1% |
±1% |
| Line regulation |
±1% |
±1% |
±1% |
±1% |
| Load regulation |
±1% |
±1% |
±1% |
±1% |
| Setup, Rise Time |
100ms,30ms/230VAC 200ms,30ms/115VAC at full load |
| Hold Up Time |
100ms/230VAC 23ms/115VAC at full load |
| Voltage Range |
88~264VAC 47~63Hz; 124~370VDC |
| AC Current |
1.2A/115V 0.8A/ 230V |
| Efficiency |
76% |
82% |
83% |
84% |
| Inrush Current |
Cold start 18A/115V 36A/230V |
| Leakage Current |
<1mA/240VAC |
| Over Load |
105%~160% rated power |
| Protection type: Constant current limiting, recovers automatically after fault condition is removed |
| Over Voltage |
5.75-6.9V |
13.8-16.2V |
17.25-20.25V |
27.6-32.4V |
| Protection type: Shut down o/p voltage, re-power on to recover |
| Working Temp., Humidity |
-20ºC~+60ºC; 20%~90% RH non-condensing |
| Storage Temp., Humidity |
-40ºC~+85ºC; 10%~95% RH |
| Temp. Coefficient |
±0.03%/ºC(0~50ºC) |
| Vibration |
10~500Hz, 2G 10min./1cycle, period for 60min, each along X, Y, Z axes |
| Withstand Voltage |
I/P-O/P: 3KVAC |
| Isolation Resistance |
I/P-O/P: 100M Ohms / 500VDC |
| Safety Standard |
Design refer to UL60950-1,TUV EN60950-1,EN50178 |
| EMC Standard |
Design refer to EN55011,EN55022,EN61000-3-2,-3,EN61000-4-2,3,4,5,6,8,11,EN55024,EN61000-6-2,EN61204-3, heavy industrial level, criteria A |
| Dimension |
78*93*56mm(W*H*D) |
| Weight |
0.3Kg |
| Packing |
48 pcs/carton/15.4KG/1.02CUFT |
| NOTE |
|
1.All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25ºC of ambient temperature.
2.Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1μ & 47μ parallel capacitor.
3.Tolerance: includes set up tolerance, line regulation and load regulation.
4.The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. |
){kind=link}